Capture Button without cord or USB to Serial Converter

Capture Button and 5.9 foot USB Cord

Retains form and functionality of the original C-Box while adding a second photo eye input for use with multiple photo eye configurations.

For EtherLynx & Vision Cameras, Includes AirLynx Gateway (8L101)

For EtherLynx & Vision Cameras. Does not include AirLynx Gateway (8L101)

Includes a 25' AC(110/220) to DC (12vdc, 1.6A) Power Supply and a DC pigtail input assembly

For EtherLynx Vision Series

For Vision-series. Includes View Finder, battery, charger, Power Supply, Clamp and HDMI cable

Includes Antenna. For Vision-series Cameras

For Vision-series. Electronically enable/disable low-light filters from FinishLynx software

For Vision-series. Allows external display to be connected to camera HDMI port for local viewing during alignment.

Allows Enhanced Scan Rate of 2000 by Pixel Density of 1000 for the EtherLynx Vision cameras.

Internal battery pack allows the camera to withstand power loss. For Vision-series.

Monitor the camera's level and orientation from FinishLynx software. For Vision-series.

Includes Antenna. For Vision-series. 5LPES not required.

Amplifies available light for better race images in low-light conditions. For Vision Series

Amplifies available light for better race images in very low-light conditions. For Vision Series

Amplifies available light for better race images in very low-light conditions. For Vision-series Lux4 to Lux8.

Enables events to be timed on all EtherLynx & Vision cameras across the network.

Allows configurable graphics display of scoreboard data via direct HDMI connection. For Vision-series.

For EtherLynx Cameras includes AirLynx Gateway 8L101.

Does not include AirLynx Gateway (8L101)

Allows use of smaller focal length lenses & extends vertical resolution of EtherLynx PRO up to 4000 pixels. Ideal for applications where camera is far from the finish line/ with wide finish lines (rowing/canoeing).

Upgrade for Vision PRO only. Includes "RAM1GB" memory upgrade to 1Gbyte.

Upgrade for Vision PRO only. Includes "RAM1GB" memory upgrade to 1Gbyte

Upgrade for Vision PRO only.

From 1024 to 2048 pixels. Upgrade for Vision PRO only.

Upgrade for Vision PRO only.

Upgrade for Vision PRO only.

2D full-frame video camera for use with FinishLynx Software. Max Resolution 1920x1080, Max Rate 30fps

Full Frame video camera for use with FinishLynx Software. Max Resolution 3264x1840, Max Rate 60fps

Full Frame video camera for use Foot Foul Visualization with FinishLynx Software.

Full Frame video camera for use Foot Foul Visualization with FinishLynx Software.

 30Watt, 56Volts

For use with IdentiLynx cameras.

8.5-50mm f1.6

Connectors, weatherproof hood at one end

Waterproof fabric cover for EtherLynx PRO camera.

Manual zoom, focus and iris control. 12.5-75mm f1.2.

Allows for Remote Controlled zoom, focus and iris.12.5-75mm f1.2

Allows for Remote Controlled Iris of F-Mount lenses on Vision Pro cameras.

Allows for Remote Controlled Iris and Remote Control Focus of F-Mount lenses on Vision Pro cameras.

Remote Iris Only

Allows remote positioning of camera's pan, tilt and swivel motion from the computer.

Allows swivel and tilt adjustment, useful with 2L200P Camera Mounting Post.

When used with tripod head, mounts camera to any pole or board

Attaches to tripod or super clamp and allows horizontal, vertical & swivel adjustment of camera.

Attaches to tripod or super clamp and allows horizontal, vertical & swivel adjustment of camera.

Replacement quick release plate for the 3275 geared head.

Attaches between camera and mounting head to allow fine horizontal adjustment.

74" Camera Tripod with Leveling Guide

105" Camera Tripod with Leveling Guide

Heavy Duty 152" Crank-Up Camera Stand w/ Wheels

Camera mounting post made from 4" aluminum with heavy wheeled base. One 12' high section.

Advanced Software with Database Integration - Windows9x/NT /2000/XP/Vista platform.

Multi-lingual software for creating FinishLynx and FieldLynx database files as well as importing and printing start lists and results. Includes many seeding options, multi-event scoring, cross-country scoring, and scoreboard interface.

Allows any EtherLynx camera to act as a photo eye and send pause & stop signals to running clocks. Also allows automatic capture of any object moving across the finish line.

Allows synchronization with external timing devices including GPS based devices

Enables FinishLynx to accept split times from external devices (e.g. transponders and Chronometers)

Remote applications to access FinishLynx event data over the network. LDP is meant for programmers with specific objectives such as streaming image frames or analyzing them using AI technology. It can also be used to poll FinishLynx for the event status.

Allows recording of multiple splits within the same FinishLynx event using a single or multiple cameras.

Incl. with FinishLynx 13.00. Allows FinishLynx to connect to serial devices such as scoreboards and wind gauges via a wired or wireless network. Required when using SeriaLynx. Also useful for ResulTV.

Allows use of RadioLynx wireless start and photocell with FinishLynx.

Allows FinishLynx to operate in Time Trial Mode where starts can be assigned to individual athletes.

An integrated display solution that combines ResulTV-VDM running on a battery-powered Windows Mini-PC in a weatherproof connection box 

Broadcast version suppresses Lynx Logo. When Combined with a Scan Converter, allows Results and Running Time to be displayed dynamically to CCTV and other TV output display devices. Connects via network or serial port to any PC running FinishLynx.

Upgrade to ResulTV-U or -P

Configurable graphics application allowing results and running time data to be dynamically displayed on LED video screens, CCTV, and other TV devices via an HDMI output. Supports network or serial port to any PC running FinishLynx, FieldLynx or LynxPad.

ResulTV-VDM is a simplified version of ResulTV. Like the VDM option for Vision-series cameras, the content of the ResulTV-VDM layout is controlled by the data received (e.g. from FinishLynx or FieldLynx)

Electronic "gun" generates a flash and an electronic gun sound or tone through a single large speaker. Comes with a headset to allow starting commands to run through the speaker as well. Can be used wired or with RadioLynx.

Used to add up to three additional speakers to Electronic Starting System.

Only for use with RadioLynx Transmitter.

For attaching gun sensor to starter's gun.

Includes RadioLynx transmitter, receiver, power supply & one 3L300R sensor. Range of up to 800m.

Includes RadioLynx long-range transmitter, receiver, power supply & one 3L300R sensor. Range of up to 5km.

For RadioLynx, ReacTime and SeriaLynx

Vision-series only. Includes Internal RadioLynx transmitter (Factory installed in Vision Camera), receiver, power supply & one 3L300R sensor. Range of up to 800m.

Vision-series. Includes Internal RadioLynx receiver (Factory installed in Vision Camera), transmitter, power supply & one 3L300R sensor. Range of up to 5km.

One receiver can accept start and photocell signals from multiple transmitters.

Particularly useful for placing a wireless photocell at the 200m point.

Useful for mounting photocell or reflector.

Includes long range single beam photocell, reflector, two tripods, banana cube adapter and radio transmitter.

Includes short range single beam photocell, reflector, two tripods, banana cube adapter and radio transmitter.

Allows photocell or reflector to be mounted at ground level.

Rechargeable, single beam photocell. 30 meter optical range

Allows radio transmitter to be mounted to photocell.

Allows two photocells or reflectors to be mounted in the same plane.

Rechargeable, single beam photocell. 15 meter optical range

Includes two 15m range single beam photocells, two reflectors, two tripods and two double mounting supports and double photocell cable

Includes one 15m range single beam photocell, one reflector, two tripods, mounting supports and photocell cable.

Allows two photocells to be connected in serial to produce one signal when both beams are broken

For use with FinishLynx. Includes tripod, case, DC Power Cord and 200' cable.

For use with FL and standalone use. Includes: Complete WG-Lynx & WG-SA-CTRL standalone controller unit

Cable only

Cable only

Connects directly to wind gauge. Battery operated. Tripod included.

For WG-Lynx for use with Field Events

3 conductor 24 awg shielded cable, 500 feet long, with XLR-3 male and female connectors.

Multiple reel cabling system for an outdoor 400m facility. Allows starter to simply plug the start sensor into an "outlet" near each of the four corners of the track.

3 conductor 24 awg shielded cable 10 feet long, with XLR-3 male and female connectors.

3 conductor 24 awg shielded cable 25 feet long, with XLR-3 male and female connectors.

3 conductor 24 awg shielded cable 50 feet long, with XLR-3 male and female connectors.

3 conductor 24 awg shielded cable 100 feet long, with XLR-3 male and female connectors.

3 conductor 24 awg shielded cable 200 feet long, with XLR-3 male and female connectors.

3 conductor 24 awg shielded cable 300 feet long, with XLR-3 male and female connectors.

With RJ45 Connectors

With RJ45 Connectors

With RJ45 Connectors

With RJ45 Connectors

Water Resistant conn for LXLED

Water Resistant conn for LXLED

A complete physical and electrical camera check-up including timer accuracy certification.

Price varies with items purchased

Price varies with items purchased

Price varies with items purchased

Connects Command Center to ReacTime computer serial port.

Allows connection of devices such as gun sensors and photocells to a Block Sensor.

Allows a single gun sensor on start button to activate 2 block sensors.

Attaches to most manufacturer's starting blocks. This sensor can be used for training or competition. Measures athlete's reaction time and relative power out of the blocks.

Connects up to 10 Block Sensors to create a complete False Start Detection and Reaction Time System.

#DPU414 - Uses paper roll # SS112-25A

Includes tripods and 50' cable.

Holds 6 Block Sensors.

Allows charging of up to 10 block sensors simultaneously.

Holds 4 Block Mounted Speakers.

Allows the analyzing, storing and printing of reaction time and relative power traces downloaded from the Command Center. Can be used to send reaction times to FinishLynx for inclusion in the data flow. Windows9x/NT/2000/XP/Vista platform.

Allows the analyzing, storing and printing of reaction time, time-to-distance and relative power traces downloaded from one or more block sensors. Windows9x/NT/2000/XP/Vista platform.

Rechargeable, single beam photocell with internal radio transmitter. 15 meter optical range - Not compatible with RadioLynx.

Only for use with MG-ACC089 - Not compatible with RadioLynx.

 (Part# 7L107)

1 Seat for use with NetExchange

1 Seat for use with NetExchange

Site License. Allows FieldLynx to transfer results information to ResulTV, scoreboard displays and FieldLynx printer.

 Site license. Allows FieldLynx to communicate with a Wind Gauge

Allows connection of LaserLynx EDM directly to FieldLynx.

NetExchange Server allows FieldLynx, ClerkLynx and AirCyber applications to retrieve and send Lynx Database files to the competition management computer.

Includes WG, Laser & SB. Allows field interfacing to WG-Lynx, WG-Sonic, Lasers & Scoreboards

Windows OS, USB Ports, Wired/Wireless Ethernet

Laser based electronic distance measurement (EDM) system. Meets or exceeds World Athletics accuracy requirements. Includes tripod, prism, prism pole, on-board battery and data cable.

For LaserLynx Pro II, Pro III and HS II

For LaserLynx Pro III, Pro II, LaserLynx HS II

 End box with loop wire of 6M/9M/12M

End box (6m/9m/12m loop wire)

With 16m loop wire

With 50m coax

With 100m coax

(US, AUS, MY, CN, JP)

(US, AUS, MY, CN, JP)